top of page


Muster Foam based Fire Suppression Systems are the most suitable solution for the protection of assets where liquid hydrocarbon fuels pose a high fire risk. Water alone is ineffective and can even be dangerous. The introduction of foam amplifies the effectiveness of water by breaking down the surface tension, making the droplets smaller, and enhancing the cooling effect.

The role of the foam in the solution is to create a blanket sealing the vapours preventing ignition. The role of the water in the solution is to provide cooling. Foams are supplied in concentrates that are appropriately proportioned with water. They are then aspirated with nitrogen gas to produce the foam bubbles and discharged through a pre-engineered Fire Suppression System specifically designed to protect the risk areas. A Muster Foam System can be used as a standalone Fire Suppression system or in conjunction with IPS or SAG as a dual agent system.

  • Solution-based agents suitable for mobile vehicles & fixed plant

  • Environmentally responsible Fluorine Free options available

  • Direct application with superior cooling effects

  • Operating range from -40°C to +60°C

  • Cylinder sizes from 15 litres to 110 litres

AFFF Group Photo_2020.jpg


Alarm Panel 2022.jpg

The heart of every electronic Muster Fire Suppression System is our exclusive alarm panel. The Muster Alarm Panel is an advanced integrated device that provides a complete solution which incorporates control, monitoring, and activation of our Muster Fire Suppression Systems. Depending on the requirements of the installation or the customer, the Alarm Panel is configured to support either LHD or LOP fire detection.


Manufactured from a single piece of billet stainless steel, our cylinder valves are designed to provide the reliability and performance you expect from an engineered fire suppression system. Depending on the application and system configuration, Muster cylinder valves can be either electronic or pneumatically activated.

Actuater 2.jpg

Available in either push-button or a lever design, Muster Remote Actuators are manufactured from the same high quality stainless steel used throughout the Muster range. Available in both electronic LHD and pneumatic LOP versions, Remote Actuators enable the operator to trigger activation of the fire suppression system manually at the first sign of a potential fire.


MusterWire is the detection method used in our electronic (LHD) fire suppression systems and is available in various temperature ratings to suit any application. MusterWire has a high-performance fluoro jacket giving it superior protection from abrasion, chemical permeation, weather and direct sunlight. The core of the wire consists of two strands of conductive wire that are separated by a heat sensitive polymer. When the wiring is exposed to the rated temperature, the polymer melts and the twin strands arc and send a signal to the Muster Alarm Panel which the actuates the fire Suppression System.


The Muster Diagnostics Module allows technicians to leverage all of the innovations built into the Muster Alarm Panel. The multiple screen display shows real time information relating to alarm panel parameters, system pressure, battery status, software updates and other information required to comprehensively maintain your fire suppression system.  Further information is available by downloading the data logs from the diagnostics module onto a PC using the Muster Diagnostics Application.



  • Fully controlled by the Alarm Panel

  • 24/7 Fire detection monitoring

  • 24/7 Cylinder actuation monitoring

  • Electrical detection & actuation

  • Reliable & fast signal reaction time

  • Uses its own power source

  • Lowest cost of installation

  • Very low periodic servicing costs

  • Fully controlled by the Alarm Panel

  • 24/7 Fire detection monitoring

  • 24/7 Cylinder actuation monitoring

  • State of the art pressure transducers

  • Automatic or Manual actuation

  • Uses its own power source

  • High quality stainless steel components

  • Very low periodic servicing costs

  • Designed primarily for underground use

  • Eliminates all electronic components

  • Manual activation using LOP actuators

  • High-quality stainless steel components

  • Pneumatic solenoid shuts off the fuel supply

  • Solenoid to be sourced separately

  • Combine SAG & Foam on one piece of equipment

  • Extend fire protection to multiple risk areas

  • Centrally managed by a single Alarm Panel

  • Combine IPS & Foam on one piece of equipment

  • Extend fire protection to multiple risk areas

  • Centrally managed by a single Alarm Panel

bottom of page